Study on the removal of olefins from naphtha by clay loaded with trifluoromethanesulfonic acid

Journal of Porous Materials - In this work, a trifluoromethanesulfonic acid (TFOH) modified clay (TFOH-Clay) was developed for the removal of trace olefins in heavy naphtha. 5%TFOH-Clay can...     

Eco-friendly approach for preparation of hybrid silica aerogel via freeze drying method

Journal of Materials Science - In this paper, an eco-friendly method of producing hybrid silica aerogels by freeze-drying method (FD) is proposed. In the freeze-drying system, deionized water was...     

红心火龙果发酵液喷雾干燥工艺优化及红心火龙果籽油的研究

以红心火龙果发酵液作为研究对象,通过优化喷雾干燥工艺制备粉剂,最佳工艺条件为:20%麦芽糊精,进液量:10mL/min,进口温度为120℃,出口温度为65℃;得到的粉剂为紫红色粉末,益生菌含量达到108cfu/g以上,口感酸甜。将发酵后的火龙果籽进行提取,得到的火龙果籽油含有丰富的十六酸、亚油酸和油酸。     

Surface energies in high-entropy carbides with variable carbon stoichiometry

The carbon vacancy in high-entropy carbides (HECs) has a significant impact on their physical and chemical properties, yet relevant studies have still been relatively few. In this study, we investigate the surface energies of HECs with variable carbon vacancies through first-principles calculations. The results show that the surface energy of the (1 0 0) surface of the stoichiometric HECs is significantly lower than that of (1 1 1) surface. With the decrease in carbon stoichiometry, the surface energies of both (1 0 0) and (1 1 1) surfaces increase gradually, which is mainly due to the weakening of covalent bonding and the decrease of metal Hirshfeld-I (HI) charges. However, the surface energy of (1 0 0) surface increases more quickly than that of (1 1 1) surface and will exceed that of (1 1 1) surface when the carbon stoichiometry decreases to a certain extent, which is primarily attributed to the greater decrease rate of metal HI charges of (1 0 0) surface.     

基于重要度排序的配电自动化终端优化布局方法

针对配电自动化终端优化布局问题，提出了一种基于重要度排序的终端优化布局方法。首先以等年值综合费用为目标函数，供电可靠性和投入产出比为双重约束建立了配电自动化终端优化布局模型。然后通过分析配电自动化终端对供电可靠性提升的影响，给出各个节点的“二遥”及“三遥”终端安装重要度定义及计算公式。最后采用枚举法确定最优终端安装数量，基于节点终端安装重要度排序确定终端的最优安装位置。该方法考虑了已布局节点对剩余节点终端安装重要度的影响，能够在降低计算量的同时兼顾布局合理性。运用所提方法RBTS-BUS2系统及扩充模型进行终端优化布局并与智能优化算法的布局结果进行对比，验证了本文方法的有效性及优越性。     

盾构接收对地铁车站接收端的影响研究

以西安地铁14号线某区间盾构接收施工为依托,通过数值模拟手段,对比分析了接收端结构板在不同施作时机条件下,盾构出洞对接收端影响并提供最优盾构接收方案.研究表明,接收端仅结构中板完成条件下盾构接收对接收端结构的影响,要明显小于接收端仅底板完成条件下接收的影响.在实际施工中,中板完成后盾构接收还应重点控制接收端端头加固质量、保证接收端混凝土结构达到强度要求,同时盾构接收过程中加强监测点的布设及监测频次.研究结果对类似工程具有一定的指导意义及参考价值.     

Oxidative characteristics and gel properties of porcine myofibrillar proteins affected by l-lysine and l-histidine in a dose-dependent manner at a low and high salt concentration

This study investigated the effects of l -lysine (Lys) and l -histidine (His) on the oxidative characteristics and gel properties of porcine myofibrillar proteins (MP). Results showed that Lys and His had a strong ferrous ion-chelating ability and hydroxyl radical-scavenging activity. Moreover, Lys and His inhibited the protein carbonyl formation and MP aggregation at 0.2 M and 0.6 M NaCl, respectively, in a dose-dependent manner. Furthermore, 2 and 4 mg mL⁻¹ Lys and His decreased the oxidation-induced loss of the tertiary structure of MP accompanied by the lower surface hydrophobicity. The water-holding capacity and gel strength of MP gels increased with increasing Lys and His concentrations due to more regular and lamellar structures with smaller and homogeneous pores at 0.6 M NaCl and more orderly crosslinking via fibrous filament at 0.2 M NaCl. In summary, Lys and His chelated the ferrous ions and scavenged hydroxyl radicals, decreased the oxidation-induced physicochemical changes, thus preventing oxidative damage during the formation of a three-dimensional gel network, which resulted in better gel quality.     

Fabrication of high-efficiency Yb:Y2O3 laser ceramics without photodarkening

High-efficiency Yb:Y₂O₃ laser ceramics were fabricated using the vacuum-sintering plus hot isostatic pressing (HIP) without sintering additives. High-purity well-dispersed nanocrystalline Yb:Y₂O₃ powder was synthesized using a modified co-precipitation method in-house. The green bodies were first vacuum sintered at a temperature as low as 1430°C and then HIPed at 1450°C. Finally, the samples were air annealed at 800°C for 10 h. Although no sintering aids were used, full density of the samples with excellent optical homogeneity and an inline transmission of 80% at 400 nm could be obtained. Moreover, photodarkening phenomenon was not detected in the ceramics. Preliminary laser experiment with the fabricated ceramics in a two-mirror cavity has demonstrated 32 W continuous-wave (CW) output at ∼1077 nm with an optical-to-optical conversion efficiency of 58.2%. To the best of our knowledge, this is so far the highest CW output power and optical-to-optical conversion efficiency achieved with the Yb³⁺-doped sesquioxide ceramics in a simple two-mirror cavity.